C
ClearView News

How much does a 60 ml TPO roll weigh?

Author

Jessica Burns

Published Mar 14, 2026

How much does a 60 ml TPO roll weigh?

Weight: TPO: 45 mil is 0.23 pounds per square foot, 60 mil is 0.31 pounds per square foot. PVC: 45 mil is 0.30 pounds per square foot, 60 mil is 0.40 pounds per square foot. Attachment options: Mechanically attached, fully adhered, ballasted (TPO).

Also know, what size rolls does TPO come in?

OPTIONS: Thicknesses: 45, 60, 72 and 80 mil product. Roll Widths: 4,6,8,10, 12 feet. Colors: Gray, Tan and White.

Beside above, how much does a roll of TPO cost? Roof

MaterialQuantityUnit Price
GenFlex 60 mil TPO (10′ x 100′)2 rolls$562.50
GenFlex Peel & Stick Flashing (12″ x 25′)1 roll$178.87
GenFlex Peel & Stick Cover Tape (6″ x 100′)3 rolls$257.75
GenFlex Peel & Stick TPO Pipe Boot (1″-6″)2 pcs.$33.44

Regarding this, what is thicker 45 mil or 60 mil?

(A mil is a unit of measure where 1-mil is equal to 0.001 inches. So, a 45-mil roofing membrane is actually 0.045 inches thick; whereas a 60-mil membrane is 0.06 inches thick, and so on.)

What is GAF TPO?

An advanced synthetic low-slope roofing membrane from the largest roofing manufacturer in North America – GAF. Everguard TPO is a single-ply roofing membrane that offers excellent performance, at a very cost-effective price. Heat-welded seams providing for superior strength.

What is the R value of 60 TPO?

Weight – 0.36 lb. per square foot. Colors – White, tan, gray and dark gray. R-Value – 0.1 ft2?°F?hr/Btu.

How long does TPO roof last?

It comes in a variety of thickness ranging from 45 mil to 80+ mil which can fit within a wide variety of budgets. On average TPO roofs come with up to a 30 years warranty and with the appropriate maintenance, it is not uncommon for a TPO roofing system to last as long as 30 years.

Can you put TPO over existing roof?

Can TPO be installed over an existing roof system? But once all the existing insulation and decking has been inspected and approved, a TPO system can be installed after an insulation board has been applied over an existing built-up roof system or another single ply membrane.

Is TPO expensive?

Generally speaking, TPO roofing will cost between $3.00 and $5.00 per square foot to install. This is slightly more expensive than what you'll find with a tar and gravel roof option, but can be a bit more cost effective than the normal prices seen with the installation of a PVC roofing system.

Is TPO roofing good?

TPO is very good at resisting dirt build-up, punctures, and tears as well. The use of TPO on your roof can mean lower cooling costs due to UV resistance. While TPO is energy efficient, it is also made from environmentally friendly products. So, TPO can actually help to lower carbon emissions.

How wide is TPO roofing?

TPO Roofing Membrane, 6 feet wide, 60 mil, WHITE (per foot)

How thick is 60 mils?

Visit our page for our plastic broken down by thickness.
milmminch
150.3810.015
200.5080.02
300.7620.03 1/32 in.
601.5240.06 1/16 in

Does TPO shrink?

TPO does not shrink over time, but PVC can and this will cause many problems on a roofing job.

How thick should a rubber roof be?

According to Righteous Rubber Roofing, there are three thickness options: 45 Mil, 60 Mil, and 90 Mil. A Mil is a unit of measurement denoting a thousandth of an inch. A 45 Mil EPDM roofing membrane is about as thick as a dime.

What is Thickness over scrim?

Thickness above scrim

(aka “Performance Layer”) While it's commonly believed that thicker membranes offer superior protection, it's important to note where that thickness comes from. The top layer of a membrane – also known as the “performance” layer - is the most vulnerable.

What is the life expectancy of a rubber roof?

50 years

What is the thickest EPDM?

EPDM membrane is manufactured in various thicknesses (.045″ to .090″ thick) and is available as a non-reinforced or reinforced sheet (depending upon application). Other thicknesses are also available for use in non-roofing applications as a special order.

How thick is PVC roofing?

Typically, PVC welds hold strong over time. It's supplied in 60 mil (1.5 mm) or 80 mil (2 mm) thick sheets, though a good portion of the thickness is taken up by the reinforcement scrim. There is PVC cure polymer material, which is the actual waterproofing, above and below this scrim.

How thick is a 45 mil pond liner?

45/1000 of an inch

Is TPO a rubber roof?

The term TPO stands for Thermoplastic Polyolefin. Believe it or not, TPO is actually in a broad family of rubber roofing materials. TPO is a blend of polypropylene and ethylene-propylene rubber. It is a synthetic rubber derived from oil and natural gas (ethylene propylene).

How is TPO roofing calculated?

For a decent quality TPO membrane, pricing starts at $5.50-6.00 per square foot installed, without tear-off. For example, if you have a 1,500 sq. ft. roof, you total installation cost for TPO will be $8,500-9,000.

Which is better EPDM or TPO?

TPO has better dimensional stability than EPDM. EPDM is more likely to shrink which can cause a variety of problems on your roof.

Is TPO more expensive than shingles?

When comparing the price of rubber roofing with that of asphalt roofing, rubber roofing typically costs $300 to $400 per square, at the time of publication. Although rubber roofing is more expensive, it usually lasts twice as long as asphalt shingles and additionally saves on energy costs.

How big is a square of TPO?

Like other types of roofing, TPO systems are priced in 100 square foot sections, commonly called “squares”.

What does a roll of TPO weigh?

Weight: TPO: 45 mil is 0.23 pounds per square foot, 60 mil is 0.31 pounds per square foot. PVC: 45 mil is 0.30 pounds per square foot, 60 mil is 0.40 pounds per square foot. Attachment options: Mechanically attached, fully adhered, ballasted (TPO).

Who makes the best TPO roofing?

GAF, North America's largest roofing manufacturer, has maintained that its EverGuard Extreme® TPO is the best-performing TPO available in the market.

What is the minimum slope for a TPO roof?

Thermoplastic single-ply roofing systems are plastic sheets (PVC, TPO, CSPE) that are welded together with hot air. This creates a shingle sheet that provides the weather protection for the building. Both the Thermoset and the Thermoplastic must be installed at a minimum one- fourth-inch-per-twelve-inch slope.

Who manufactures TPO roofing?

TPO Certified by Major Manufacturers

Carlisle SynTec. GAF. Johns Manville. Firestone.

Are there different types of TPO?

Those types include: Thermoplastic Polyolefin (TPO) Ethylene Propylene Diene Terpolymer (EPDM)

Can you paint a TPO roof?

Yes, TPO can be painted using a suitable primer and paint. There are specialized coatings for TPO. You can hire roofing experts for this.

What is TPO roofing made of?

Each thermoplastic polyolefin layer is made of ethylene-propylene rubber and manufactured with fillers such as talc, fiberglass, and carbon fiber. These fillers add to the TPO's strength and flexibility.

How do you clean a TPO roof?

Use a soft-bristled, long-handled brush or floor broom with a cleaning solution consisting of a mild, non-abrasive household detergent and water to clean the surface of the roof membrane, taking care to not damage the top surface of the membrane.

How many squares are in a roll of TPO roof?

TPO Accessories
Size
8' Roll
Full Roll Weight204 lb. (93 kg)
Full Roll Size8' x 100' (2.44 x 30.5 m) (800 sq. ft.[74.3 m²])
5' Roll

What does TPO roof stand for?

Thermoplastic polyolefin

Continue Reading

Wie bekomme ich Magenta TV?

What is pension provident fund?

How do I fix error code 183?

How much does a 60 ml TPO roll weigh?